SABO™ PPS (Polyphenylene Sulfide) Series - Wuhu SABO New Material Technology Co., Ltd

You are here: Home > Products > Sheet Specifications >

SABO™ PPS (Polyphenylene Sulfide) Series

High heat resistance, chemical resistance, and high rigidity.

PPS (Polyphenylene Sulfide), also known as the "Plastic Gold," is a semi-crystalline, high-performance thermoplastic resin. It features high mechanical strength, high heat resistance (long-term service temperature of approximately 220°C), excellent chemical resistance, flame retardancy, good thermal stability, and outstanding electrical properties.
PPS-ST is based on PPS reinforced with high-performance glass fibers, significantly enhancing the rigidity and strength of the material, though its toughness is lower than that of neat PPS.

138 6712 5881

Downloads

Key Features

Excellent dimensional stability due to low coefficient of linear thermal expansion and low water absorption

Continuous service temperature up to 220°C; note that the glass transition temperature is only 90°C, so caution is required for use under high load at elevated temperatures

Excellent fatigue and creep resistance

Stable dielectric constant and dissipation factor over a wide frequency range

Applications

Semiconductor

We provide high-purity, antistatic, and acid/alkali-resistant engineering plastics for precision components such as wafer carriers, packaging and testing equipment, and cleanroom accessories.

Aerospace

We specialize in lightweight, high-temperature-resistant, flame-retardant, and weather-resistant materials for applications such as cabin interiors, structural components, insulation parts, and precision aviation assemblies.

Automotive Manufacturing

We focus on lightweight, insulating, flame-retardant, and chemical-resistant materials for new energy vehicle battery, motor, and electronic control systems (three-electric systems), connectors, interior and exterior trim, and structural functional components.

Medical Devices

We utilize biocompatible, sterilizable, and hydrolysis-resistant medical-grade materials for diagnostic equipment, surgical instruments, and sterile structural components.

Energy Sector

We provide weather-resistant, insulating, corrosion-resistant, and high/low-temperature-resistant materials and structural components for photovoltaic, wind power, and energy storage applications.

Industrial Sector

We supply high-rigidity, wear-resistant, and self-lubricating materials for general components such as automation equipment, gears and bearings, pumps and valves, and fixtures and jigs.

Performance Parameters

	Test Item	Test Method	Test Conditions	Unit	SABO™ PPS	SABO™ PPS (ST)
Mechanical Properties	Tensile Strength	ASTM D638	23℃	MPa	79	165
	Tensile Elongation	ASTM D638	23℃	%	23	2
	Flexural Strength	ASTM D790	23℃	MPa	126	233
	Flexural Modulus	ASTM D790	23℃	GPa	3.3	11.8
	Izod Impact Strength	ASTM D256	J/m	J/m	15	157
	Rockwell Hardness	ASTM D785	23℃	M-scale	M95	M80
Thermal Properties	Heat Deflection Temperature	ASTM D648	-	℃	112	260
Thermal Properties	Continuous Service Temperature	-	-	℃	220	220
Electrical Properties	Dielectric Strength	ASTM D149	-	MV/m	15	18
	Surface Resistance	ASTM D257	-	Ω	10¹⁶	10¹⁶
	Volume Resistance	ASTM D257	-	Ω·cm	10¹⁸	10¹⁶
Physical Properties	Density	ASTM D792	23℃, 4℃ H2O	-	1.35	1.59
	Water Absorption	ASTM D570	23℃ , 24 h	%	0.02	0.02
	Coefficient of Linear Thermal Expansion	JIS K7197	-	×10⁻⁵/℃	2.4~2.9	1.7~6.8
	Flammability	ASTM D570	-	-	V-0 equivalent	V-2 (0.8mm)

*The values shown are typical values and are not guaranteed.